How to Properly Regrout and Recaulk the shower or bath


I do not look dirty shower, dirty and black? There are many ways to regrout and recaulk shower or bath, but there's really only one way to do the job properly, so the shower remains waterproof, stainproof and look beautiful for years to come.

first step is to thoroughly clean the shower. A lot of dirty soap scum showers accumulation should be thoroughly cleaned before any regrouting process begins. It is important that a professional soap scum remover products, and professional scrub pad to rub the dirt and soap scum on your shower walls and floor. Do not use any abrasive scrub pad, because they scratch the tiles. It may be useful to utilize a professional steam cleaning machine with soap scum remover and scrub pads. The truckmounted professional steam cleaner is useful to accelerate the cleaning process, but the professional soap scum remover and scrub pads, as well as a fair amount of elbow grease can be very effective in removing all the soap scum private shower walls and floor.

The second step is to remove the dirty, moldy grout and seal. It is important that you first remove all old gasket and got into the shower. The best way to remove the old seal is to use a razor blade tool and scrape it all around and inside the shower. Once the old seals have been removed now it's time to remove the grout in the shower. Many devices, such as a Dremel tool or Rotozip this, but the best tool in the hands of a Multimaster Fein Supercut vibrating tools or diamond bit. It is important to use every tool Fein grout lines and clear all lines with a stiff brush to make sure the new mortar will adhere to a stable base.

The third step is to dry up the wall. In most cases, a little water, mold and hit the wall. It is therefore necessary to thoroughly and completely dry before you shower walls regrouting process is taking place. Do not try regrout on top of a wet shower wall surface. The water in the walls continue to harbor dangerous mold and mildew. Also in the mix is ​​properly due to moisture on the walls, and change color and flake away in a very short period of time. The best way to dry out the shower walls are a professional dehumidifier for at least 3-7 days. So you can be sure the shower wall will be dry, and all the walls of this mold dies before you start regrouting.

apply

Fourth step, the grout in the shower. It is best to have a professional grout powder mixed with a latex additive, do not use pre-mixed and ready to use products, as they are much worse, and it is technically not cement at all. It is best to go to a professional tile store and purchase injecting equipment from an experienced agent. Try to stay away from the big box home improvement stores as many inferior products and their sales people do not usually specialize in tile setting products.

Step Five recaulk the shower. The seal is the weakest link in the water damaging the walls and the floor, so it is important that we should apply the correct tile wall between the gasket between the flat and the fixtures and tiles. This ensures that the water can not get between the wall and into the walls and floors. It is best to only 100% silicone sealant. 100% silicone seal lasts the longest, and will not allow mold to grow, cheaper than the water-based latex or silicone based sealants.

Step Six seals. It is important to seal the grout professional impregnation sealing. The high quality lacquer protects the grout from stains and prevent mold from forming. Here, too, we recommend that you purchase a professional paint a tile store, sealants and stay away from the cheaper it is sold at the big box stores.

Seventh step is to wait 72 hours. Wait 72 hours for the grout and seal the entire treatment and then go and enjoy the new look showers. The procedure can be done regrouting many homeowners with the right tools and some handyman skills. It's also very convenient and save a lot of headaches to a professional cleaning and restoration of tile and grout professionally regrout company and recaulk the shower or bath.

How to hire a professional contractor Regrouting. Make sure that you have questions regrouting potential entrepreneur, and do not settle for cheap and incomplete days regrouting recaulking procedure. One day regrouting looks sloppy procedures and mortar and seal will fail in a short period of time. One day regrouting procedures are also not all potential water damage to the walls. It also does not accept the company that only thin coats of new grout over the old grout. The skim coat process will not last and will only be a short time before the skim coated with mortar starts to chip and flake away. Furthermore, the new mortar trap water between the two layers of mortar is caused by the shower water sealing system fails. Interest on the national labor and industry, as well as the Better Business Bureau (BBB) ​​to check that the potential contractor is fully licensed and insured and has no unresolved Better Business Bureau complaints may indicate a shoddy job.

Source by Troy Roberts

Leave a Reply

Your email address will not be published. Required fields are marked *